FE version 1.0.37-5.4 for BCM96358 (32bit,SP,BE) Build Date: 2009年 03月 31日 星期二 17:07:55 CST (root@localhost.localdomain) Copyright (C) 2000-2005 Broadcom Corporation. Boot Address 0xbfc00000 Initializing Arena. Initializing Devices. Parallel flash device: name MX29LV320AB, id 0x22a8, size 4096KB 798 875 0x6:0x11f 0x6:0x108 0x6:0x108 CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz Total memory: 33554432 bytes (32MB) Total memory used by CFE: 0x80401000 - 0x80533000 (1253376) Initialized Data: 0x8041C0E0 - 0x8041CDD0 (3312) BSS Area: 0x8041CDD0 - 0x80431000 (82480) Local Heap: 0x80431000 - 0x80531000 (1048576) Stack Area: 0x80531000 - 0x80533000 (8192) Text (code) segment: 0x80401000 - 0x8041C0D8 (110808) Boot area (physical): 0x00533000 - 0x00573000 Relocation Factor: I:00000000 - D:00000000 Board IP address : 192.168.1.1 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id Name : 96358GW Psi size in KB : 24 Number of MAC Addresses (1-32) : 10 Base MAC Address : 00:22:6b:fc:9f:d8 Ethernet PHY Type : Internal Memory size in MB : 32 CMT Thread Number : 0 get pid2 at0xbffd886a pid checked! *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Code Address: 0x80010000, Entry Address: 0x80230018 Decompression OK! Entry at 0x80230018 Closing network. Starting program at 0x80230018 Linux version 2.6.8.1 (yaowen@yaowen-desktop) (gcc version 3.4.2) #1 Wed Jun 30 21:01:42 CST 2010 Parallel flash device: name MX29LV320AB, id 0x22a8, size 4096KB 96358GW prom init CPU revision is: 0002a010 Determined physical RAM map: memory: 01fa0000 @ 00000000 (usable) On node 0 totalpages: 8096 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 4000 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 Built 1 zonelists Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 brcm mips: enabling icache and dcache... Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes. Primary data cache 16kB 2-way, linesize 16 bytes. PID hash table entries: 128 (order 7: 1024 bytes) Using 150.000 MHz high precision timer. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 29216k/32384k available (1891k kernel code, 3124k reserved, 280k data, 92k init, 0k highmem) Calibrating delay loop... 299.82 BogoMIPS Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Checking for 'wait' instruction... unavailable. NET: Registered protocol family 16 Total Flash size: 4096K with 71 sectors File system address: 0xbfc10100 Scratch pad is not used for this flash part. Can't analyze prologue code at 801e745c Initializing Cryptographic API PPP generic driver version 2.4.2 NET: Registered protocol family 24 Using noop io scheduler bcm963xx_mtd driver v1.0 Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. mymtd = 81f82c00 Creating 5 MTD partitions on "Physically mapped flash": 0x00010100-0x00309100 : "fs" mtd: partition "fs" doesn't start on an erase block boundary -- force read-only 0x00010000-0x003e0000 : "tag+fs+kernel" 0x00000000-0x00010000 : "bootloader" 0x003f0000-0x00400000 : "nvram" 0x003e0000-0x003f0000 : "ath_data" brcmboard: brcm_board_init entry Serial: BCM63XX driver $Revision: 1.1.1.1 $ ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX blaadd: blaa_detect entry adsl: adsl_init entry Broadcom BCMPROCFS v1.0 initialized u32 classifier NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) ip_conntrack version 2.1 (253 buckets, 0 max) - 408 bytes per conntrack ip_ct_h323: init success ip_conntrack_pptp version 2.1 loaded ip_conntrack_rtsp v0.01 loading ip_nat_h323: init success ip_nat_pptp version 2.0 loaded ip_nat_rtsp v0.01 loading ip_tables: (C) 2000-2002 Netfilter core team netfilter PSD loaded - (c) astaro AG ipt_random match loaded NET: Registered protocol family 1 NET: Registered protocol family 17 Ebtables v2.0 registered NET: Registered protocol family 8 NET: Registered protocol family 20 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 92k freed init started: BusyBox v1.00 (2010.06.30-13:06+0000) multi-call binary init started: BusyBox v1.00 (2010.06.30-13:06+0000) multi-call binary Starting pid 38, console /dev/ttyS0: '/usr/etc/rcS' Algorithmics/MIPS FPU Emulator v1.5 bcm_enet: module license 'Proprietary' taints kernel. Broadcom BCM6358A1 Ethernet Network Device v0.3 Jun 30 2010 21:00:14 Config Ethernet Switch Through MDIO Pseudo PHY Interface dgasp: kerSysRegisterDyingGaspHandler: eth0 registered eth0: MAC Address: 00:22:6B:FC:9F:D8 losetup: /dev/mtdblock5: No such device or address mount: Mounting /dev/loop0 on /tmp/fs1 failed: No such device or address * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=adsl action=start /bin/cp /proc/uptime /tmp//var/run/rc.adsl.run /usr/sbin/adslctl start --up BcmAdsl_Initialize=0x8011A4C8, g_pFnNotifyCallback=0x80221644 AnnexCParam=0x2AAF5140 AnnexAParam=0x00000980 adsl2=0x004009B0 pSdramPHY=0xA1FFFFF8, 0x1B78EE 0xDEADBEEF AdslCoreSharedMemInit: shareMemAvailable=13328 AdslCoreHwReset: AdslOemDataAddr = 0xA1FFBB64 AnnexCParam=0x2AAF5140 AnnexAParam=0x00000980 adsl2=0x004009B0 dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered /usr/sbin/adslctl configure --mod a AnnexCParam=0x7FFF7868 AnnexAParam=0x00000980 adsl2=0x00000000 /usr/sbin/atmctl stop /usr/sbin/atmctl start ATM proc init !!! device eth0 entered promiscuous mode * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=ethwan action=start /bin/cp /proc/uptime /tmp//var/run/rc.ethwan.run * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=printk action=start /bin/cp /proc/uptime /tmp//var/run/rc.printk.run * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=lan action=start /bin/cp /proc/uptime /tmp//var/run/rc.lan.run /sbin/ifconfig br0 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255 /usr/bin/killall dhcp-fwd killall: dhcp-fwd: no process killed * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=wlan action=create /bin/cp /proc/uptime /tmp//var/run/rc.wlan.run * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=wlan action=start /bin/cp /proc/uptime /tmp//var/run/rc.wlan.run ==============> Goto start wifi [ create_wsc_config ] wsc_configured = <1> =======================WPA-PSK2============== uconfig.encrytype = 8 uconfig.encrytype = ===========> Init WIFI use flash data eep->baseEepHeader.version:e016,e sum:ffff ath0 * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=fast_br action=start /bin/cp /proc/uptime /tmp//var/run/rc.fast_br.run /sbin/rmmod fast_br /sbin/insmod /lib/modules/fast_br.ko "if1=eth0" "if2=ath0" "br_if=br0" mac = NOT NULL mac = 00226BFC9FD9 mac = NOT NULL mac = 00226BFC9FD9 wlan up!! start wifi return 0 * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=syslogd action=start /bin/cp /proc/uptime /tmp//var/run/rc.syslogd.run /usr/bin/killall -SIGUSR2 syslogd killall: syslogd: no process killed * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=httpd action=start /bin/cp /proc/uptime /tmp//var/run/rc.httpd.run mac = NOT NULL mac = 00226BFC9FD9 /bin/rm /tmp/www -f /bin/ln -sf /www.eng /tmp/www /usr/sbin/mini_httpd -d /tmp/www -r "Linksys WAG160Nv2 " -c '*.cgi' -t 300 -i /var/run/mini_httpd.pid -S -E /usr/sbin/certSrv.pem & * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=dhcpd action=start /bin/cp /proc/uptime /tmp//var/run/rc.dhcpd.run /usr/sbin/udhcpd /etc/udhcpd.conf& * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=ntp action=start /bin/cp /proc/uptime /tmp//var/run/rc.ntp.run /usr/sbin/ntp -z GMT+10 1& * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=route action=start /bin/cp /proc/uptime /tmp//var/run/rc.route.run * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=ripd action=start /bin/cp /proc/uptime /tmp//var/run/rc.ripd.run /usr/sbin/iptables -D INPUT -p udp --dport 520 -j ACCEPT iptables: Bad rule (does a matching rule exist in that chain?) rm: cannot remove `/tmp/hnap_connectting': No such file or directory l2_packet_receive - recvfrom: Network is down * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=upnp action=start /bin/cp /proc/uptime /tmp//var/run/rc.upnp.run /usr/bin/killall -9 upnpd killall: upnpd: no process killed route add -net 239.0.0.0 netmask 255.0.0.0 br0 /usr/sbin/upnpd ppp0 br0 30 4& UPnP Initialized Intialized UPnP with fullurl=http://192.168.1.1:49152/gateway.xml ipaddress=192.168.1.1 port=49152 web_dir_path=/usr/upnp/ desc_doc_url=http://192.168.1.1:49152 Specifying the webserver root directory -- /usr/upnp/ Registering the RootDevice RootDevice Registered Initializing State Table fullurl http://192.168.1.1:49152/gateway.xml pWsccb->wscIe = 0 Advertisements Sent * * * * * * * {~._.~} * * ( Y ) * * ()~*~() * * (_)-(_) * * * * * * ap_name=wscupnp action=start /bin/cp /proc/uptime /tmp//var/run/rc.wscupnp.run /usr/sbin/wscupnpd br0 ath0 30 4& Please press Enter to activate this console.